Model PRO-OE4BS
Transmitter Programming Guide
This transmitter makes use of icons (symbols) to identify the reaction your
system will have when any icon (button) is pressed. These icons are
programmed at time of installation to meet the needs of the individual and to
complement the vehicle that the system is installed in. To replace a transmitter
or add transmitters, please follow the programming instructions listed on the
pages of this manual.
RECEIVER
CHANNEL
SYSTEM FUNCTION
BUTTON
Lock and arm.
Also remote panic if alarm system is installed
1
Unlock and disarm.
With 2 step unlock option, press a second
time for all doors.
2
Remote panic if alarm system is installed
Press and hold for optional trunk release
activation, press 2 times to activate remote
start.
3
4
Press and release for optional device, press
and hold for extended output.
OPTION
NOTE: Additional devices or a second vehicles may be programmed to
operate by pressing a combination of buttons shown below, check
with your installation center for programming these additional
functions or features.
q
q
q
q
q
Lock + Unlock
Lock + Trunk
Unlock + Trunk
Lock + Opt.
q
q
q
q
q
Lock + Unlock + Opt.
Lock + Unlock + Trunk
Unlock + Opt. + Trunk
Lock + Opt + Trunk
Unlock + Opt.
Lock + Unlock + Trunk + Opt.
128-5868
1 of 6
Released 9-8-00.
"Repeat step 4 for each transmitter you wish to program".
NOTE: Any button(s) of the transmitter may be used in place of the lock
symbol button for channel 1, however using the proper symbol
will obviously be less confusing for the consumer.
5) Press and release the valet push-button program switch once to ad-
vance to channel 2. The dash mounted LED will Flash 2 times, indicat-
ing that the unit is ready to accept programming for the disarm/unlock
channel # 2.
6) Press and hold the unlock symbol button of the transmitter you wish to
program for 4 seconds or until a long chirp is heard from the siren, or the
interior/parking lights flash.
"Repeat step 6 for each transmitter you wish to program".
NOTE: Any button(s) of the transmitter may be used in place of the unlock
symbol button for channel 2, however using the proper symbol will
obviously be less confusing for the consumer.
7) Press and release the valet push-button program switch once to ad-
vance to channel 3. The dash mounted LED will Flash 3 times, indicat-
ing that the unit is ready to accept programming for the trunk release/
remote start, channel # 3 output.
8) Press and hold the trunk/key symbol button of the transmitter you wish
to program for 4 seconds or until a long chirp is heard from the siren, or
the interior/parking lights flash.
"Repeat step 8 for each transmitter you wish to program".
NOTE: Any button(s) of the transmitter may be used in place of the trunk
symbol button for channel 3, however using the proper symbol will obvi-
ously be less confusing for the consumer.
9) Press and release the valet push-button program switch once to ad-
vance to channel 4. The dash mounted LED will Flash 4 times, indicat-
ing that the unit is ready to accept programming for optional device
connected to channel # 4.
10) Press and hold the option button of the transmitter you wish to program
for 4 seconds or until a long chirp is heard from the siren, or the interior/
parking lights flash.
"Repeat step 10 for each transmitter you wish to program".
3
128-5868
3 of 6
NOTE: Certain systems may have additional receiver channels, if your
unit exits the program during the next press of the pushbutton
switch, your system has 4 channels only, if when you press valet
push-button program switch once to advance to channel 5. The
dash mounted LED will Flash 5 times, indicating that the unit is
ready to accept programming for the 5th channel option.
Press and hold any unused button combination as indicated on the front
cover of this manual for 4 seconds or until a long chirp is heard from the
siren, or the interior/parking lights turn flash.
NOTE: Certain systems may have additional receiver channels, if your
unit exits the program during the next press of the pushbutton
switch, your system has 5 channels only, if when you press valet
push-button program switch once to advance to channel 6. The
dash mounted LED will Flash 6 times, indicating that the unit is
ready to accept programming for the 6th channel option.
Press and hold any unused button combination as indicated on the front
cover of this manual for 4 seconds or until a long chirp is heard from the
siren, or the interior/parking lights turn flash.
NOTE: Panic is pre-assigned to operate with the lock button and unlock
buttons of the transmtter. Please see owners manual for addi-
tional information under the heading Panic Feature.
128-5868
4 of 6
BATTERY REPLACEMENT:
The transmitter incorporates a small LED visible through the case which
is used to indicate battery condition. You will notice a decrease in operat-
ing range as the battery condition deteriorates. To replace the battery:
1) Remove the small # 0 phillips head screw from the rear of the case.
2) Remove the top cover to access the discharged battery paying atten-
tion to the proper polarity orientation.
3) Remove and properly dispose of the discharged battery.
4) Insert the new battery, close the case, then reinstall the small case
screw removed in step 1.
GP 27 A Battery
5
128-5868
5 of 6
ORDER FORM FOR 4 BUTTON
TRANSMITTER MODEL NO. PRO-OE4BS
Important: To help us expedite your order, please print all of the
information legibly and mail this form and your payment
according to the instructions below.
Note: Order PD-40 for Blue transmitter buttons.
Order PD-41 for Red transmitter buttons.
1) Pad Number:_____________________________________
2) Name: __________________________________________
3) Address: ________________________________________
4) City:____________ State: ____ Zip Code: __________
5) Telephone Number: (
)
6) Total Number Of Transmitters Required:
Cost Per Transmitter is:
Multiply By Number Of Transmitters
7) Enter Total Amount Enclosed
$65.00
X
(New York State Residents must include the appropriate sales tax)
8) Method of Payment:
Mastercard
Visa
Check or Money Order
(do not send cash)
Make Checks Payable To Audiovox Corporation
Credit Card Number: _________________________________
Credit Card Expiration Date:
/
/
9) Mail this form along with your payment to:
Audiovox Electronics Corp., 150 Marcus Blvd. Hauppauge, NY, 11788
Attn.: TRANSMITTER DEPARTMENT
128-5868
128-5868
6 of 6
|